Datsun 280ZX Parts

Welcome to our great selection of new Nissan Datsun 280ZX parts 1979 to 1983. We are often asked if our parts are new and original. The answer is yes. Absolutely. Check out the following links for your specific Nissan Datsun needs. We at NEW DATSUN PARTS are always looking for new suppliers of parts for the models listed on our site. If by chance you have some new Datsun parts I’d be very interested. 

DATSUN 280ZX RIGHT REAR TAIL LAMPS

CORRECT FOR 1979 TO 1983 MODEL YEARS COMES WITH GASKETS,WIRING HARNESS WITH BULBS

THIS ITEM IS 100% GENUINE OEM FROM NISSAN, BRAND NEW

CLICK ON PHOTO TO SEE LARGER PHOTO

PART: ZX01 (NO LONGER AVAILABLE) *

DATSUN 280ZX RIGHT REAR TAIL LAMPS

CORRECT FOR 1979 TO 1983 MODEL YEARS COMES WITH GASKETS,WIRING HARNESS WITH BULBS

THIS ITEM IS 100% GENUINE OEM FROM NISSAN, BRAND NEW

CLICK ON PHOTO TO SEE LARGER PHOTO

PART: ZX01 $375.00 US$*

DATSUN 280ZX REAR TAIL LAMP GASKETS

CORRECT FOR 1979 TO 1983 MODEL YEARS

THIS ITEM IS 100% GENUINE OEM FROM NISSAN, BRAND NEW

CLICK ON PHOTO TO SEE LARGER PHOTO

PART: ZX02 $85.00 A SET *

DATSUN 280ZX AIR FILTER

CORRECT FOR 1979 TO 1980 MODEL YEARS

THIS ITEM IS 100% GENUINE OEM FROM NISSAN, BRAND NEW

CLICK ON PHOTO TO SEE LARGER PHOTO

PART: ZX03 $(NO LONGER AVAILABLE) *

DATSUN 280Z MIRROR LEFT DOOR

. APPLIED MODEL: *2S +*4S; (10/1978 - 08/1981)

THIS ITEM IS 100% GENUINE OEM FROM NISSAN, BRAND NEW

CLICK ON PHOTO TO SEE LARGER PHOTO

PART: ZX04 $175.00 US*

FRONT STRUTS BUMP STEER SPACERS A SET OF 2

Bump steer spacers made in North America  They reduce the bump steer on your lowered Datsun with the addition of these 20.32 Millimeter thick spacers. Made from 6061 t6 aluminum comes with gold anodizing. Fits between bottom of strut & steering knuckle, hi tensile bolts supplied Suits struts with 80mm bolt space

Spacers are used when lowering the front of the car. They sit between the steering arms and strut to preserve the original roll steer angle. By correcting the angle of the lower control arm they will restore the original suspension geometry. Sometimes called strut spacers or bump steer adjusters, but the purpose is not actually to do either. When the car is lowered significantly over standard, the suspension arms are closer to parallel with the ground and the tie rods are inclined up instead of down. Additionally, the steering linkage is no longer optimal.

CLICK ON PHOTO TO SEE LARGER PHOTO

PART:  CIN07 $65.00 US A SET *

DATSUN ALUMINUM BLACK ANODIZED COIL-OVER HARDWARE KIT

DESIGNED FOR USE WITH 2-INCH SERIES STEEL BODY FRONT STRUTS.

KITS INCLUDE PARTS FOR 2 FRONT STRUTS:

* X2 6 INCH ALUMINUM TREADED SLEEVE

* X2 SPRING CAP

* X2 SPRING CAP BEARING KIT

* X2 SPRING SEAT ADJUSTER NUTS

* X2 SPRING CAP RETAINER RING

* 4X RETAINER RINGS TO WELD ONTO STRUT

CLICK ON PHOTO TO SEE LARGER PHOTO

PART: CIN11 $199.00 US EACH SET *



To Order or General Inquiry
Ordering and Shipping Information
Back to 280ZX Parts Page